Short description
Bus controller | CAN I/O slave |
General information
B&R ID code | 0x1F1D |
Status indicators | Module status, bus function, data transfer, terminating resistor |
Diagnostics | |
Module status | Yes, using LED status indicator and software |
Bus function | Yes, using LED status indicator |
Data transfer | Yes, using LED status indicator |
Terminating resistor | Yes, using LED status indicator |
Power consumption | |
Bus | 1.5 W |
Additional power dissipation caused by actuators (resistive) [W] | - |
Certifications | |
CE | Yes |
UKCA | Yes |
ATEX |
Zone 2, II 3G Ex nA nC IIA T5 Gc IP20, Ta (see X20 user's manual) FTZÚ 09 ATEX 0083X |
UL |
cULus E115267 Industrial control equipment |
HazLoc |
cCSAus 244665 Process control equipment for hazardous locations Class I, Division 2, Groups ABCD, T5 |
KC | Yes |
Interfaces
Electrical properties
Electrical isolation |
CAN I/O isolated from I/O CAN I/O not isolated from bus |
Operating conditions
Mounting orientation | |
Horizontal | Yes |
Vertical | Yes |
Installation elevation above sea level | |
0 to 2000 m | No limitation |
>2000 m | Reduction of ambient temperature by 0.5°C per 100 m |
Degree of protection per EN 60529 | IP20 |
Ambient conditions
Temperature | |
Operation | |
Horizontal mounting orientation | -25 to 60°C |
Vertical mounting orientation | -25 to 50°C |
Derating | - |
Storage | -40 to 85°C |
Transport | -40 to 85°C |
Relative humidity | |
Operation | 5 to 95%, non-condensing |
Storage | 5 to 95%, non-condensing |
Transport | 5 to 95%, non-condensing |
![](/fileadmin/X20BC0073.right-90b73ca0.jpg)
Material number:
X20BC0073Description:
- Fieldbus: CAN bus
- Automatic firmware update via the fieldbus
- Integrated I/O access in B&R Automation Studio
- Integrated terminating resistor
The bus controller makes it possible to connect X2X Link I/O nodes to CAN I/O. CAN I/O is a transfer protocol based on standard CAN bus that is fully integrated in the B&R system.
Up to 43 logic I/O modules can be connected to the bus controller. Up to 16 of them can be analog modules.
With multifunction modules, the bus controller supports only the default function model in the event of automatic configuration by the bus controller (see the respective module description).
Mandatory Accessories
System modules for bus controllers
X20BB80 | X20 bus base, for X20 base module (BC, HB, etc.) and X20 power supply module, X20 end cover plates (left and right) X20AC0SL1/X20AC0SR1 included |
X20PS9400 | X20 power supply module, for bus controller and internal I/O power supply X2X Link power supply |
X20PS9402 | X20 power supply module, for bus controller and internal I/O power supply, X2X Link supply, supply not galvanically isolated |
Terminal blocks
0TB2105.9010 | Accessory terminal block, 5-pin, screw clamp terminal block 2.5 mm² |
0TB2105.9110 | Accessory terminal block, 5-pin, push-in terminal block 2.5 mm² |
X20TB12 | X20 terminal block, 12-pin, 24 VDC keyed |
Aktualizacja Automation Studio HW | Version (Date) | Download |
---|---|---|
V2.6 HW Upgrade (X20BC0073) | EXE / 1 MB | |
V2.6 HW Upgrade (X20BC0073a) | EXE / 581 KB | |
V3.0 HW Upgrade (X20BC0073) | EXE / 2 MB | |
V3.0 HW Upgrade (X20BC0073a) | EXE / 581 KB | |
V4.0 HW Upgrade (X20BC0073) | EXE / 1 MB |
Dokumentacja | Version (Date) | Download |
---|---|---|
Data sheet X20BC0073 | PDF / 954 KB | |
Installation- / EMC-Guide | PDF / 20 MB | |
X20 System User´s Manual | PDF / 7 MB |
E-CAD (szablony Electro lub EPLAN) | Version (Date) | Download |
---|---|---|
X20 EPLAN P8 from V2.4 | EXE / 160 MB |
M-CAD (Mechan. szablony) | Version (Date) | Download |
---|---|---|
3D File DXF/STEP X20 Bus Controller CAN/DeviceNet | ZIP / 28 KB | |
Dimensions PDF X20 Bus Controller CAN/DeviceNet | PDF / 4 KB |