Short description
I/O module | 4 digital outputs for controlling external power triacs or non-parallel thyristors |
General information
Digital outputs
Variant | Opto-triac |
Circuit | Normally open contact |
Nominal voltage | 48 to 240 VAC |
Max. voltage | 264 VAC |
Rated frequency | 47 to 63 Hz |
Nominal current at 25°C | |
Nominal output current | 80 mA |
Total nominal current | 320 mA |
Current over entire temperature range | |
Output current | 50 mA |
Summation current | 200 mA |
Connection type | 2-wire connections |
Zero-crossing detection | Yes |
Holding current | Max. 3.5 mA |
Leakage current | Max. 1.5 mA (per channel) |
Residual voltage (on-state voltage) | Max. 3 V |
Phase-angle control | |
Area | 5 to 95% |
Resolution | 1% |
Accuracy (60 to 240 VAC) | <100 μs |
Voltage monitoring L - N | No |
Recommended wiring | Twisted pair cabling to the terminal pairs |
Line length | Max. 10 m |
Overvoltage protection between L and N | Yes |
Insulation voltages | |
Channel - Bus | Tested at 2300 VAC |
Channel - Channel | Tested at 2300 VAC |
Protective circuit | |
External | Generally fuse |
Internal | Snubber circuit (RC element) and varistor |
Electrical properties
Electrical isolation | Channel isolated from channel, bus and I/O power supply |
Operating conditions
Mounting orientation | |
Horizontal | Yes |
Vertical | Yes |
Installation elevation above sea level | |
0 to 2000 m | No limitation |
>2000 m | Not permitted |
Degree of protection per EN 60529 | IP20 |
Ambient conditions
Temperature | |
Operation | |
Horizontal mounting orientation | -25 to 60°C |
Vertical mounting orientation | -25 to 50°C |
Derating | - |
Storage | -40 to 85°C |
Transport | -40 to 85°C |
Relative humidity | |
Operation | 5 to 95%, non-condensing |
Storage | 5 to 95%, non-condensing |
Transport | 5 to 95%, non-condensing |
Mechanical properties
Note |
Order 1x terminal block X20TB32 separately. Order 1x bus module X20BM12 separately. |
Pitch | 12.5+0.2 mm |
Materiaalnummer:
X20DO4613Omschrijving:
- 4 digital outputs
- Controls external power triacs or non-parallel thyristors
- Outputs with 48 - 240 VAC
- 50 Hz or 60 Hz
- Outputs electrically isolated from one another
- Phase-angle control
- Zero-crossing detection
- Negative half-waves can be switched off
- 2-wire connections
- 240 V coding
- OSP mode
- Frequency mode
The module is a digital output module that is equipped with 4 opto-triac outputs using phase-angle control. L and N are fed to the module for zero-crossing detection.
The 4 outputs are electrically isolated from one another and are used for controlling external power triacs or nonparallel thyristors.
Vereiste toebehoren
Automation Studio HW Upgrades | Versie (Datum) | Download |
---|---|---|
V2.7 HW Upgrade (X20DO4613) | EXE / 1 MB | |
V3.0 HW Upgrade (X20DO4613) | EXE / 2 MB | |
V4.0 HW Upgrade (X20DO4613) | EXE / 1 MB |
Documentatie | Versie (Datum) | Download |
---|---|---|
Data sheet X20DO4613 | PDF / 2 MB | |
Installation- / EMC-Guide | PDF / 20 MB | |
X20 Package leaflet ATEX/CSA | PDF / 2 MB | |
X20 System User´s Manual | PDF / 7 MB |
E-CAD (Electro of EPLAN Templates) | Versie (Datum) | Download |
---|---|---|
X20 EPLAN P8 from V2.4 | EXE / 160 MB |
M-CAD (Mechan. Templates) | Versie (Datum) | Download |
---|---|---|
3D File DXF/STEP X20 Electronic module | ZIP / 10 KB | |
3D File STEP X20 I/O-Slice | ZIP / 872 KB | |
Dimensions PDF X20 Electronic module | PDF / 3 KB |