X20DMF320

Short description

I/O module	16 digital inputs 24 VDC for 1-wire connections 16 mixed channels, 24 VDC input or output for 1-wire connections

General information

B&R ID code	0x2E86
Status indicators	I/O function per channel, operating state, module status
Diagnostics
Module run/error	Yes, using LED status indicator and software
Outputs	Yes, using LED status indicator and software (output state)
Power consumption
Bus	0.04 W
Internal I/O	2.7 W
Additional power dissipation caused by actuators (resistive) [W]	0.312 W
Certifications
CE	Yes
UKCA	Yes

Digital inputs

Quantity	6 high-speed inputs, 10 standard inputs 16 mixed channels, configuration as input or output using software
Nominal voltage	24 VDC
Input characteristics per EN 61131-2	Type 1
Input voltage	24 VDC -15% / +20%
Input current at 24 VDC	Channels 1 to 6, fast inputs: Typ. 3.2 mA Channels 7 to 16, standard inputs: Typ. 2.4 mA Channels 17 to 32, mixed channel: Typ. 2.4 mA
Input circuit	Sink
Input filter
Hardware	High-speed inputs: ≤7 μs Standard inputs and mixed channels: ≤100 μs
Software	Default 0 ms, configurable between 0 and 25 ms in 0.1 ms intervals
Connection type	1-wire connections
Input resistance	Channels 1 to 6, high-speed inputs: 7.5 kΩ Channels 7 to 16, standard inputs: 10 kΩ Channels 17 to 32, mixed channels: 10 kΩ
Additional functions	Channels 1 to 6, high-speed digital inputs: 2x 30 kHz event counting, 2x ABR incremental encoder, 2x period measurement, 2x gate time measurement, 2x counter latch function
Switching threshold
Low	<5 VDC
High	>15 VDC
Insulation voltage between channel and bus	500 V_eff

ABR incremental encoder

Quantity	2
Encoder inputs	24 V, asymmetrical
Counter size	16-bit
Input frequency	30 kHz
Evaluation	4x

Event counters

Quantity	2
Signal form	Square wave pulse
Evaluation	Rising edge, falling edge or both edges The counter is cyclical.
Input frequency	30 kHz
Counter size	16-bit

Edge detection / Time measurement

Possible measurements	Period measurement, gate time measurement
Signal form	Square wave pulse
Evaluation	Positive edge - Negative edge
Counter size	16-bit
Counter frequency
Internal	48 MHz, 24 MHz, 12 MHz, 6 MHz, 3 MHz, 1.5 MHz, 750 kHz, 375 kHz, 187.5 kHz
Length of pause between pulses	≥100 μs
Pulse length	≥20 μs

Digital outputs

Quantity	13 standard outputs, 3 high-speed outputs All outputs designed as mixed channels, configurable as inputs or outputs using software
Variant	Current-sourcing FET
Nominal voltage	24 VDC
Switching voltage	24 VDC -15% / +20%
Nominal output current	0.5 A per channel
Total nominal current	8 A
Connection type	1-wire connections
Output circuit	Source
Output protection	Thermal shutdown in the event of overcurrent or short circuit (see value "Short-circuit peak current")
Pulse width modulation
Period duration	1 to 65 ms
Pulse duration	0 to 100%
Resolution for pulse duration	0.1%
Diagnostic status	Output monitoring with 25 ms delay
Leakage current when the output is switched off	3 µA
R_DS(on)	78 mΩ
Peak short-circuit current	6.95 A
Switch-on in the event of overload shutdown or short-circuit shutdown	Approx. 3 ms (depends on the module temperature)
Switching delay
0 → 1	≤300 μs
1 → 0	≤300 μs
Switching frequency
Resistive load	Standard outputs: Max. 500 Hz High-speed outputs: Max. 1 kHz
Braking voltage when switching off inductive loads	Typ. 53 VDC
Insulation voltage between channel and bus	500 V_eff

Electrical properties

Electrical isolation	Channel isolated from bus Channel not isolated from channel

Operating conditions

Mounting orientation
Horizontal	Yes
Vertical	Yes
Installation elevation above sea level
0 to 2000 m	No limitation
>2000 m	Reduction of ambient temperature by 0.5°C per 100 m
Maximum	4000 m
Degree of protection per EN 60529	IP20

Ambient conditions

Temperature
Operation
Horizontal mounting orientation	-25 to 60°C
Vertical mounting orientation	-25 to 45°C
Derating	See section "Derating".
Storage	-40 to 85°C
Transport	-40 to 85°C
Relative humidity
Operation	5 to 95%, non-condensing
Storage	5 to 95%, non-condensing
Transport	5 to 95%, non-condensing

Mechanical properties

Note	Order clamping blocks separately (see section "Order data").
Pitch	27.5^+0.2 mm

Materiaalnummer:

X20DMF320

Omschrijving:

16 digital inputs
Sink circuit
2 counter inputs with 30 kHz counter frequency
ABR incremental encoder
Period duration / gate time measurement
16 mixed channels optionally as input or output
Source circuit
Integrated output protection
3 PWM outputs
All channels with 1-wire connections

The module is equipped with 16 inputs and 16 mixed channels, optionally as input or output in 1-wire technology. The outputs are designed for a source output circuit, and the inputs are designed for a sink circuit.

Optionele toebehoren

Terminal blocks

X20TBS1	Terminal block set for X20 I/O module: 2x 16-pin terminal block
X20TBS2	Terminal block set for X20 I/O module: 8x 4-pin terminal block

Automation Studio HW Upgrades	Versie (Datum)	Download
V4.0 HW Upgrade (X20DMF320)		EXE / 1 MB Login voor downloaden
V6.0 HW Upgrade (X20DMF320)		EXE / 1 MB Login voor downloaden

Certificaten	Versie (Datum)	Download
EU Declaration of conformity PLC X20		PDF / 169 KB Login voor downloaden

Documentatie	Versie (Datum)	Download
Data sheet X20DMF320		PDF / 1 MB Login voor downloaden
Installation- / EMC-Guide		PDF / 20 MB Login voor downloaden
X20 System User´s Manual		PDF / 7 MB Login voor downloaden

E-CAD (Electro of EPLAN Templates)	Versie (Datum)	Download
Makro-/Artikeldaten 4.0.5 (X20DMF320)		EXE / 2 MB Login voor downloaden

M-CAD (Mechan. Templates)	Versie (Datum)	Download
3D files DXF/STEP X20DMF320		ZIP / 2 MB Login voor downloaden