General information
Support | |
Dynamic node allocation (DNA) | Yes |
Slots for plug-in modules | 1 |
Mains connection
DC bus connection
DC bus capacitance | 1880 µF |
24 VDC power supply
Motor connection
Motor holding brake connection
Braking resistor
Peak power int./ext. | 1.5 kW / 11 kW |
Continuous power int./ext. | 100 W / 970 W |
Minimum braking resistance (ext.) | 12 Ω |
Enable inputs
Encoder interfaces
Trigger inputs
Quantity | 2 |
Circuit | Sink |
Electrical isolation | |
Input - ACOPOS P3 | Yes |
Input - Input | Yes |
Input voltage | |
Nominal | 24 VDC |
Maximum | 30 VDC |
Switching threshold | |
Low | <5 V |
High | >15 V |
Input current at nominal voltage | Approx. 4 mA |
Switching delay | |
Rising edge | <2 µs |
Falling edge | <1 µs |
Modulation compared to ground potential | Max. ±38 V |
Temperature sensor connection
Quantity | 1 |
Resistance range | 500 Ω to 5 kΩ |
Support
Software | |
ACP10 | V3.13.0 |
Operating conditions
Permissible mounting orientations | |
Hanging vertically | Yes |
Standing horizontally | In preparation |
Installation elevation above sea level | |
Nominal | 0 to 500 m |
Maximum | 4000 m |
Pollution degree per EN 61800-5-1 | 2 (non-conductive pollution) |
Overvoltage category per EN 61800-5-1 | III |
Degree of protection per EN 60529 | IP20 |
Ambient conditions
Temperature | |
Operation | |
Nominal | 5 to 40°C |
Maximum | 55°C |
Storage | -25 to 55°C |
Transport | -25 to 70°C |
Relative humidity | |
Operation | 5 to 85%, non-condensing |
Storage | 5 to 95% |
Transport | 95% at 40°C |
Mechanical properties
Dimensions | |
Width | 66 mm |
Height | 290 mm |
Depth | |
Wall mounting | 258.5 mm (with 8EXA front cover: 261 mm) |
Weight | 3.2 kg |
Numero materiale:
8EI8X8MWS11.0700-1Descrizione:
ACOPOS P3 servo drive, 1 digital multi-standard encoder interface per axis, 3x 200-230 VAC, 1x 110-230 VAC, 8.8 A, 1 axis, dual use, wall mounting, two-row connector set, cover, integrated braking resistor
accessori opzionali
Display modules
8EAD0000.000-1 | Display module, LCD, 128 x 64, black/white, 1x USB 3.0 |
Front covers
8EXA100.0010-00 | ACOPOS P3 cover, B&R orange, single-width, suitable for servo drives 8EI1X6xxSxx.xxxx-x / 8EI2X2xxSxx.xxxx-x / 8EI4X5xxSxx.xxxx-x /8EI8X8xxSxx.xxxx-x |
Shield component sets
8SCSE01.0100-00 | ACOPOS P3 shield component set: 1x ACOPOS P3 shield mounting plate, 1x 2x M3x6 screws |
8SCSE02.0100-00 | ACOPOS P3 shield component set: 1x shield connection clamp type SK14 |
8SCSE02.0200-00 | ACOPOS P3 shield component set: 1x shield connection clamp type SK20 |
Terminal blocks
8TB2104.2210-00 | 4-pin push-in terminal block, 1-row, pitch: 5.08 mm, label 1: Numbered consecutively |
Terminals
8TB2104.2210-50 | 4-pin push-in terminal block, yellow, 1-row, with locking mechanism, pitch: 5.08 mm, label 1: 4 3 2 1 |
8TB2204.2210-50 | 4-pin push-in terminal block, yellow, 2-row, pitch: 5.08 mm, label 1: 4 3 2 1, |
8TB3102.222C-20 | 2-pin push-in terminal block, 1-row, with locking mechanism, pitch: 7.62 mm, label 2: COM 24 V, coding C: 10 |
8TB3103.222A-20 | 3-pin push-in terminal block, 1-row, with locking mechanism, pitch: 7.62 mm, label 2: PE RB- RB+, coding A: 000 |
8TB3106.223C-20 | 6-pin push-in terminal block, 1-row, with locking mechanism, pitch: 7.62 mm, label 3: PE L3 N(L2) L1 DC- DC+, coding C: 000010 |
8TB3202.222C-40 | 2-pin push-in terminal block, 2-row, with locking mechanism, pitch: 7.62 mm, label 2: COM 24 V, coding C: 10 |
8TB3206.223C-40 | 6-pin push-in terminal block, 2-row, with locking mechanism, pitch: 7.62 mm, label 3: PE L3 N(L2) L1 DC- DC+, coding C: 000010 |
8TB3308.222A-00 | 4+4-pin push-in terminal block 1-row / 2-row, pitch: 7.62 mm, label 2: T- B- T+ B+ PE W V U coding A: 0000 |
Certificati | Versione (data) | Download |
---|---|---|
E225616 UL Certificate of Compliance ACOPOS P3 | PDF / 241 KB |
Documentazione | Versione (data) | Download |
---|---|---|
ACOPOS P3 User´s Manual | PDF / 175 MB | |
Datasheet 8EI8X8MWS10.XXXX-1 | PDF / 939 KB |