DWL@DWL10000783350
| Version | Langue | Système d'exploitation | Date | Taille | Type | Téléchargement |
|---|---|---|---|---|---|---|
| 1.5.2.0 | * | 29/04/2024 | 6 Mo | EXE | AS4_HW_X90CP172.24-00.exe | |
| Description |
V4.9 HW Upgrade (X90CP172.24-00) Revision information X90CP172.24-00 Version 1.5.2.0: ID: 786535 Chapter "Configuration" added to documentation Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\60334_1.fp(32), 2\60334_1.fp(54) Version 1.5.1.0: ID: 785750 Enhancementsfor AS6/AR6 - configurable IpForwarding. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 785765 New datasheet version 2.10 Channel description changed:No Configuration description changed: No Firmware changed: No Firmware: 1\60334_1.fp(32), 2\60334_1.fp(54) Version 1.5.0.0: ID: 780585 Error in AB counter mode fixed. When a channel was configured as "Digital input source", the "Counter" Register was not reset to zero after reboot. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 1\60334_1.fp(32), 2\60334_1.fp(54) Version 1.4.6.0: ID: 762065 / Support ID: 400392864 X2X bus output cycle trigger error correction The X2X bus outputcycle trigger was not started although it was configured. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\60334_1.fp(24), 2\60334_1.fp(50) Version 1.4.4.0: ID: 729190 / Support ID: 400352024 Support for 6 A current on parallel channels When two 6 A channels are used in parallel mode, a total current of 12 A isnow possible. Attention: When using 4 A and 6 A channels in parallel, each channel can only supply 4 A. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\60334_1.fp(24), 2\60334_1.fp(50) Version 1.4.3.0: ID: 714635 Module documentation revised Data sheet V1.90 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\60334_1.fp(24), 2\60334_1.fp(50) Version 1.4.1.0: ID: 710700 Add "DeviceID" and "DeviceSerialNumber" to IO Map Using the entries "DeviceID" and "DeviceSerialNumber" the serial and id of the device can now be used in the IO map. Channel description changed: Yes Configuration description changed: No Firmwarechanged: No Firmware: 1\60334_1.fp(24), 2\60334_1.fp(50) Version 1.4.0.0: ID: 684695 Module documentation revised Data sheetV1.81 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 685890 Module documentation revised Data sheet V1.81 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 703140 Enables second CPU core for I/O processing The I/O input processing can be assigned to the the second CPU core. This frees CPU processing powerto be used by the application. Channel description changed: Yes Configuration description changed: Yes Firmware changed: No Firmware: 1\60334_1.fp(24), 2\60334_1.fp(50) Version 1.3.1.0: ID: 694885 Support data point StorageWear, wear level of storage medium starting fromAR A4.90 Channel description changed: Yes Configuration description changed: No Firmware changed: No Firmware: 1\60334_1.fp(24), 2\60334_1.fp(50) Version 1.3.0.0: ID: 693000 Enable TFTP server To enable a firmware update for mobile panels, the TFTP Server must beactivated. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\60334_1.fp(24), 2\60334_1.fp(50) Version 1.2.4.0: ID: 673575 Description of "Total Current" changed to 0-45 A Channel description changed: Yes Configuration description changed: No Firmware changed: No Firmware: 1\60334_1.fp(24), 2\60334_1.fp(50) Version 1.2.3.0: ID: 668095 AS4.8 Enhancement CPU configuration: Loss of remanent data Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 1\60334_1.fp(24), 2\60334_1.fp(50) Version 1.2.2.0: ID: 656125 Improved I/O Minimal requirements AS version 4.7.1 and AR 4.71 New functions: Analogue Channels Resistor measurement 0-50 kOhm Temperature measurement PT1000 Current measurement: 4-20 mA Digital Output Channels: Adjustable maximum current 0-4 A PWM Channels: H-Bridge mode Dithering Adjustable maximum current 0-4 A / 0-6 A up to 4 kHz in PWM mode, up to 8 kHz im H-brigde mode Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 1\60334_1.fp(24), 2\60334_1.fp(50) Version 1.0.3.0: ID: 617575 / Support ID: 400261388 Corrupted CAN messages on IF9 (CAN3) With heavy load on the processor interface a "race condition" may exist onthe CAN control for IF9 (CAN3). As a result, the register access and the dataaccess may interfere. For solving this "race condition" a locking mechanism has been added, that allows data access to the CAN component only after the configuration via register accesses have been finished. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 620290 / Support ID: 400249041 Improve help on Sensor Supply status. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 1\60334_1.fp(24) Version 1.0.2.0: ID: 573925 Support X90CP172.24-00 Important Remark: To use the help, a minimum version 4.3.5.24 of the Automation Studio Main Help is required. Otherwise the upgrade is installed, but the help pages are empty. In case you installed the upgrade in the wrong order, you mustfirst uninstall the Main Help using the Windows Control Panel, installthe Main Help again and then apply the Module Upgrade. Channel description changed: Yes Configuration description changed: Yes Firmware changed: Yes Firmware: 1\60334_1.fp(23) |
|||||
