Short description
I/O module 4 digital outputs for switching electromechanical loads, pulse width modulation
General information
B&R ID code 0xEC21
Status indicators I/O function per channel, operating state, module status
Diagnostics
Module run/error Yes, using LED status indicator and software
Outputs Yes, using LED status indicator and software (output error status)
Power consumption
Bus 0.01 W
Internal I/O 1.4 W
External I/O Corresponding to external load
Additional power dissipation caused by actuators (resistive) [W] -
Certifications
CE Yes
UKCA Yes
ATEX Zone 2, II 3G Ex nA nC IIA T5 Gc
IP20, Ta (see X20 user's manual)
FTZÚ 09 ATEX 0083X
UL cULus E115267
Industrial control equipment
Digital outputs
Nominal voltage 24 VDC
Nominal output current 0.75 A
Total nominal current 3 A
Connection type 1-wire connections
Output circuit Sink
Output protection Thermal shutdown in the event of overcurrent or short circuit, integrated protection for switching inductive loads
Pulse width modulation
Period duration 1 ms (1 kHz) or 20 µs (50 kHz)
Pulse duration 0 to 100%
Resolution for pulse duration 1%
Inrush current 1.5 A for max. 25 ms
Braking voltage when switching off inductive loads 27 VDC
Reverse polarity protection No (must be protected externally)
Output voltage
Minimum 18 VDC
Nominal 24 VDC
Maximum 48 VDC
Protective circuit
External 24 VDC power supply - maximum current 10 A (melting fuse)
Electrical properties
Electrical isolation Bus isolated from channel and internal I/O power supply
Channel not isolated from channel and internal I/O power supply
Operating conditions
Mounting orientation
Horizontal Yes
Vertical Yes
Installation elevation above sea level
0 to 2000 m No limitation
>2000 m Reduction of ambient temperature by 0.5°C per 100 m
Degree of protection per EN 60529 IP20
Ambient conditions
Temperature
Operation
Horizontal mounting orientation 0 to 50°C
Vertical mounting orientation 0 to 40°C
Derating -
Storage -25 to 70°C
Transport -25 to 70°C
Relative humidity
Operation 5 to 95%, non-condensing
Storage 5 to 95%, non-condensing
Transport 5 to 95%, non-condensing
Mechanical properties
Note Order 1x terminal block X20TB12 separately.
Order 1x bus module X20BM11 separately.
Pitch 12.5+0.2 mm
Materiálové číslo:
X20CM4323
Popis:
  • 4 digital outputs
  • Control of PWM output signals based exactly on NetTime
  • 4x oversampling output functions
  • Integrated output protection
  • 24 VDC and GND for actuator power supply

The module has digital outputs for connecting electromechanical loads (e.g. valves and relays) and additional functions such as edge generation.

With a resolution down to 125 ns, the module makes it possible to set switching operations at exactly specified moments.

The following operating modes can optionally be supplemented with PWM functionality:

  • Direct I/O
  • Oversampled I/O
  • Edge generator
  • Edge generator in toggle operation for output patterns such as digital cam switches (e.g. digital cam switch of function block "ASMcDcsTimedDigitalCamSwitch")

Additional functions:

  • PWM modulation of outputs for setting the overexcitation and holding current.
  • Configuration of each channel by specifying PWM period duration
  • Control value for overexcitation current, holding current and overexcitation time
  • Possibility of disabling high-speed cutoff
Povinné příslušenství
Bus modules
X20BM11 X20 bus module, 24 VDC keyed, internal I/O power supply connected through
X20BM15 X20 bus module, with node number switch, 24 VDC keyed, internal I/O power supply connected through
Terminal blocks
X20TB12 X20 terminal block, 12-pin, 24 VDC keyed
Automation Studio HW Upgrades Verze (datum) Ke stažení
V4.0 HW Upgrade (X20CM4323) EXE / 2 MB
Certifikáty Verze (datum) Ke stažení
E115267 UL CoC X20 PDF / 1 MB
EU Declaration ATEX X20 PDF / 218 KB
EU Declaration of conformity PLC X20 PDF / 169 KB
UK Declaration PLC X20 PDF / 151 KB
Dokumentace Verze (datum) Ke stažení
Data sheet X20CM4323 PDF / 614 KB
Installation- / EMC-Guide PDF / 20 MB
X20 System User´s Manual PDF / 7 MB
E-CAD (Electro or EPLAN Templates) Verze (datum) Ke stažení
X20 EPLAN P8 from V2.4 EXE / 160 MB
M-CAD (Mechan. Templates) Verze (datum) Ke stažení
3D File DXF/STEP X20 Electronic module ZIP / 10 KB
3D File STEP X20 I/O-Slice ZIP / 872 KB
Dimensions PDF X20 Electronic module PDF / 3 KB

Vyberte prosím zemi a jazyk

B&R Logo