DWL@DWL10000300360
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
|---|---|---|---|---|---|---|
| 1.10.13.0 | * | 20.03.2024 | 3 MB | EXE | AS4_HW_X67SC4122.L12.exe | |
| Popis |
V4.0 HW Upgrade (X67SC4122.L12) Revision information X67SC4122.L12 Version 1.10.13.0: ID: 780215 Correction of the input filter with set "Filter off". Correction of the input filter, if a "Filter off" is set and a channel error is detected. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 7\42918_1.fw(340) Version 1.10.12.0: ID: 710680 Timing of module internal communication updated The timing of the module internal communication was updated. Sporadic errors 98818, 119317, 99348, 102914, 99350 no longer occur. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 710850 Limit values for the module cycle time adjusted The limit values for the calculation and monitoring of module cycle time and slot time adjusted. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 7\42918_1.fw(333) Version 1.10.11.0: ID: 692830 Improvement of the feedback diagnosis. Improvement of the feedback diagnosis of the output. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 692735 Improvement of the internal voltage monitoring. Improvement of the internal voltage monitoring. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 692640 / Support ID: 400299371 Loss of safety connection Loss of safety connection, even though the parametrized "safe data duration" is longer than the network failure Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 7\42918_1.fw(332) Version 1.10.9.2: ID: 673060 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(330) Version 1.10.9.1: ID: 643220 data sheet V1.141 See chapture "Version history" in the data sheet. i.a. calculation of Safety response time has been updated. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(330) Version 1.10.9.0: ID: 618290 logger entry 112174, 108078 Logger entry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(330) Version 1.10.1.1: ID: 516730 fixed internal communication problems fixed internal communication problems Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552645 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552650 Loggerentry on negativ edge of SafeModuleOK If a negativ edge on SafeModuleOK is detected, a logger entry will be generated Channel description changed: No Configuration description changed: No Firmware changed: No ID: 553760 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(325) Version 1.10.1.0: ID: 474970 Correction for FBK_Status_1 Correction for FBK_Status_1 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 516730 fixed internal communication problems fixed internal communication problems Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552645 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552650 Loggerentry on negativ edge of SafeModuleOK If a negativ edge on SafeModuleOK is detected, a logger entry will be generated Channel description changed: No Configuration description changed: No Firmware changed: No ID: 553760 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(325) Version 1.10.0.6: ID: 533065 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533155 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533175 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(320) Version 1.10.0.0: ID: 402885 / Support ID: 400142740 Step File The step file is available since 14th November 2014. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 441620 / Support ID: 400159816 EPLAN Data for pinout - file corrected EPLAN Data for pinout - file corrected Channel description changed: No Configuration description changed: No Firmware changed: No ID: 470660 Support of release 1.10 including openSAFETY 1.5 Support of release 1.10 including openSAFETY 1.5 with easier parametrization of timing parameters Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 470665 changed manual verion to 1.100 changed manual verion to 1.100 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(320) Version 1.9.1.1: ID: 425470 change of input filter The behaviour of the input filter has changed. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 425475 Update Online Help Update Online Help V1.91 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 425480 fw valid from SafetyRelease 1.4 on The firmware is used for all SafetyReleases from 1.4 on. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301) Version 1.9.0.0: ID: 286520 / Support ID: 400082173 Diagnostic coverage not relevant for users Since the parameter "Diagnostic coverage" isn't relevant for users, it was generally removed from the datasheet of all safety modules. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 413875 SafeModuleID >300 Now it is possible to set SafeModuleID greater than 300, like described in the AS-Help. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414030 Channel-Status-Info ON The default value of the Channel-Status information is now ON. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414190 added parameter "Disable OSSD" added parameter "Disable OSSD" Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414250 parameter max. Switching Frequency removed Parameter max. Switching Frequency has no meaning any more. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes ID: 414295 2-channel evaluation: additional information at warning If warning "discrepancy time elapsed" appears for 2-channel evaluation, info0 will now display the chosen PLCopen FBK (equivalent or antivalent). Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 414370 Update Online Help Update Online Help V1.90 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290), 5\42918_1.fw(300) Version 1.6.0.8: ID: 388470 The module also supports SafetyRelease 1.8 Starting with this version, the module also supports SafetyRelease 1.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.7: ID: 339300 internal Adjustments internal Adjustments Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.5: ID: 335515 The module also supports SafetyRelease 1.7 Starting with this version, the module also supports SafetyRelease 1.7 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 335520 / Support ID: 400083263 unlock of SafeModule IDs > 300 SafeModule IDs up to 1023 are now unlocked Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.0: ID: 314285 Adaption of module configuration file release 1.6 Adaption of module configuration file release 1.6 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.5.0.4: ID: 303415 Support of AutomationStudio 4.0 Support of AutomationStudio 4.0 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.5.0.3: ID: 287445 New feature Discrepancy time maximum from 500ms to 10s increased. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 290270 Datasheet Version 1.50 Datasheet version 1.50 added in Html format Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.4.1.3: ID: 284655 Release für kompatibles Safety Release 1.5 ID 284600 Parameter for backwards compatibility in description file changed Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281) Version 1.4.0.3: ID: 261780 Increase of minimum load to 12mA The minimum load was increased to 12mA in the documentationErhöhung der Mindestlast auf 12mA Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.10.12.0 | * | 16.04.2021 | 3 MB | EXE | AS4_HW_X67SC4122.L12.exe | |
| Popis |
V4.0 HW Upgrade (X67SC4122.L12) Revision information X67SC4122.L12 Version 1.10.12.0: ID: 710680 Timing of module internal communication updated The timing of the module internal communication was updated. Sporadic errors 98818, 119317, 99348, 102914, 99350 no longer occur. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 710850 Limit values for the module cycle time adjusted The limit values for the calculation and monitoring of module cycle time and slot time adjusted. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 7\42918_1.fw(333) Version 1.10.11.0: ID: 692830 Improvement of the feedback diagnosis. Improvement of the feedback diagnosis of the output. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 692735 Improvement of the internal voltage monitoring. Improvement of the internal voltage monitoring. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 692640 / Support ID: 400299371 Loss of safety connection Loss of safety connection, even though the parametrized "safe data duration" is longer than the network failure Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 7\42918_1.fw(332) Version 1.10.9.2: ID: 673060 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(330) Version 1.10.9.1: ID: 643220 data sheet V1.141 See chapture "Version history" in the data sheet. i.a. calculation of Safety response time has been updated. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(330) Version 1.10.9.0: ID: 618290 logger entry 112174, 108078 Logger entry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(330) Version 1.10.1.1: ID: 516730 fixed internal communication problems fixed internal communication problems Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552645 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552650 Loggerentry on negativ edge of SafeModuleOK If a negativ edge on SafeModuleOK is detected, a logger entry will be generated Channel description changed: No Configuration description changed: No Firmware changed: No ID: 553760 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(325) Version 1.10.1.0: ID: 474970 Correction for FBK_Status_1 Correction for FBK_Status_1 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 516730 fixed internal communication problems fixed internal communication problems Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552645 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552650 Loggerentry on negativ edge of SafeModuleOK If a negativ edge on SafeModuleOK is detected, a logger entry will be generated Channel description changed: No Configuration description changed: No Firmware changed: No ID: 553760 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(325) Version 1.10.0.6: ID: 533065 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533155 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533175 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(320) Version 1.10.0.0: ID: 402885 / Support ID: 400142740 Step File The step file is available since 14th November 2014. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 441620 / Support ID: 400159816 EPLAN Data for pinout - file corrected EPLAN Data for pinout - file corrected Channel description changed: No Configuration description changed: No Firmware changed: No ID: 470660 Support of release 1.10 including openSAFETY 1.5 Support of release 1.10 including openSAFETY 1.5 with easier parametrization of timing parameters Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 470665 changed manual verion to 1.100 changed manual verion to 1.100 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(320) Version 1.9.1.1: ID: 425470 change of input filter The behaviour of the input filter has changed. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 425475 Update Online Help Update Online Help V1.91 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 425480 fw valid from SafetyRelease 1.4 on The firmware is used for all SafetyReleases from 1.4 on. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301) Version 1.9.0.0: ID: 286520 / Support ID: 400082173 Diagnostic coverage not relevant for users Since the parameter "Diagnostic coverage" isn't relevant for users, it was generally removed from the datasheet of all safety modules. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 413875 SafeModuleID >300 Now it is possible to set SafeModuleID greater than 300, like described in the AS-Help. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414030 Channel-Status-Info ON The default value of the Channel-Status information is now ON. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414190 added parameter "Disable OSSD" added parameter "Disable OSSD" Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414250 parameter max. Switching Frequency removed Parameter max. Switching Frequency has no meaning any more. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes ID: 414295 2-channel evaluation: additional information at warning If warning "discrepancy time elapsed" appears for 2-channel evaluation, info0 will now display the chosen PLCopen FBK (equivalent or antivalent). Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 414370 Update Online Help Update Online Help V1.90 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290), 5\42918_1.fw(300) Version 1.6.0.8: ID: 388470 The module also supports SafetyRelease 1.8 Starting with this version, the module also supports SafetyRelease 1.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.7: ID: 339300 internal Adjustments internal Adjustments Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.5: ID: 335515 The module also supports SafetyRelease 1.7 Starting with this version, the module also supports SafetyRelease 1.7 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 335520 / Support ID: 400083263 unlock of SafeModule IDs > 300 SafeModule IDs up to 1023 are now unlocked Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.0: ID: 314285 Adaption of module configuration file release 1.6 Adaption of module configuration file release 1.6 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.5.0.4: ID: 303415 Support of AutomationStudio 4.0 Support of AutomationStudio 4.0 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.5.0.3: ID: 287445 New feature Discrepancy time maximum from 500ms to 10s increased. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 290270 Datasheet Version 1.50 Datasheet version 1.50 added in Html format Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.4.1.3: ID: 284655 Release für kompatibles Safety Release 1.5 ID 284600 Parameter for backwards compatibility in description file changed Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281) Version 1.4.0.3: ID: 261780 Increase of minimum load to 12mA The minimum load was increased to 12mA in the documentationErhöhung der Mindestlast auf 12mA Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.10.11.0 | * | 17.09.2020 | 3 MB | EXE | AS4_HW_X67SC4122.L12.exe | |
| Popis |
V4.0 HW Upgrade (X67SC4122.L12) Revision information X67SC4122.L12 Version 1.10.11.0: ID: 692830 Improvement of the feedback diagnosis. Improvement of the feedback diagnosis of the output. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 692735 Improvement of the internal voltage monitoring. Improvement of the internal voltage monitoring. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 692640 / Support ID: 400299371 Loss of safety connection Loss of safety connection, even though the parametrized "safe data duration" is longer than the network failure Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 7\42918_1.fw(332) Version 1.10.9.2: ID: 673060 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(330) Version 1.10.9.1: ID: 643220 data sheet V1.141 See chapture "Version history" in the data sheet. i.a. calculation of Safety response time has been updated. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(330) Version 1.10.9.0: ID: 618290 logger entry 112174, 108078 Logger entry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(330) Version 1.10.1.1: ID: 516730 fixed internal communication problems fixed internal communication problems Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552645 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552650 Loggerentry on negativ edge of SafeModuleOK If a negativ edge on SafeModuleOK is detected, a logger entry will be generated Channel description changed: No Configuration description changed: No Firmware changed: No ID: 553760 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(325) Version 1.10.1.0: ID: 474970 Correction for FBK_Status_1 Correction for FBK_Status_1 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 516730 fixed internal communication problems fixed internal communication problems Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552645 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552650 Loggerentry on negativ edge of SafeModuleOK If a negativ edge on SafeModuleOK is detected, a logger entry will be generated Channel description changed: No Configuration description changed: No Firmware changed: No ID: 553760 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(325) Version 1.10.0.6: ID: 533065 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533155 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533175 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(320) Version 1.10.0.0: ID: 402885 / Support ID: 400142740 Step File The step file is available since 14th November 2014. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 441620 / Support ID: 400159816 EPLAN Data for pinout - file corrected EPLAN Data for pinout - file corrected Channel description changed: No Configuration description changed: No Firmware changed: No ID: 470660 Support of release 1.10 including openSAFETY 1.5 Support of release 1.10 including openSAFETY 1.5 with easier parametrization of timing parameters Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 470665 changed manual verion to 1.100 changed manual verion to 1.100 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(320) Version 1.9.1.1: ID: 425470 change of input filter The behaviour of the input filter has changed. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 425475 Update Online Help Update Online Help V1.91 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 425480 fw valid from SafetyRelease 1.4 on The firmware is used for all SafetyReleases from 1.4 on. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301) Version 1.9.0.0: ID: 286520 / Support ID: 400082173 Diagnostic coverage not relevant for users Since the parameter "Diagnostic coverage" isn't relevant for users, it was generally removed from the datasheet of all safety modules. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 413875 SafeModuleID >300 Now it is possible to set SafeModuleID greater than 300, like described in the AS-Help. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414030 Channel-Status-Info ON The default value of the Channel-Status information is now ON. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414190 added parameter "Disable OSSD" added parameter "Disable OSSD" Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414250 parameter max. Switching Frequency removed Parameter max. Switching Frequency has no meaning any more. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes ID: 414295 2-channel evaluation: additional information at warning If warning "discrepancy time elapsed" appears for 2-channel evaluation, info0 will now display the chosen PLCopen FBK (equivalent or antivalent). Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 414370 Update Online Help Update Online Help V1.90 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290), 5\42918_1.fw(300) Version 1.6.0.8: ID: 388470 The module also supports SafetyRelease 1.8 Starting with this version, the module also supports SafetyRelease 1.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.7: ID: 339300 internal Adjustments internal Adjustments Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.5: ID: 335515 The module also supports SafetyRelease 1.7 Starting with this version, the module also supports SafetyRelease 1.7 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 335520 / Support ID: 400083263 unlock of SafeModule IDs > 300 SafeModule IDs up to 1023 are now unlocked Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.0: ID: 314285 Adaption of module configuration file release 1.6 Adaption of module configuration file release 1.6 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.5.0.4: ID: 303415 Support of AutomationStudio 4.0 Support of AutomationStudio 4.0 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.5.0.3: ID: 287445 New feature Discrepancy time maximum from 500ms to 10s increased. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 290270 Datasheet Version 1.50 Datasheet version 1.50 added in Html format Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.4.1.3: ID: 284655 Release für kompatibles Safety Release 1.5 ID 284600 Parameter for backwards compatibility in description file changed Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281) Version 1.4.0.3: ID: 261780 Increase of minimum load to 12mA The minimum load was increased to 12mA in the documentationErhöhung der Mindestlast auf 12mA Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.10.9.2 | * | 31.01.2020 | 3 MB | EXE | AS4_HW_X67SC4122.L12.exe | |
| Popis |
V4.0 HW Upgrade (X67SC4122.L12) Revision information X67SC4122.L12 Version 1.10.9.2: ID: 673060 Adaptations for Automation Studio 4.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(330) Version 1.10.9.1: ID: 643220 data sheet V1.141 See chapture "Version history" in the data sheet. i.a. calculation of Safety response time has been updated. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(330) Version 1.10.9.0: ID: 618290 logger entry 112174, 108078 Logger entry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(330) Version 1.10.1.1: ID: 516730 fixed internal communication problems fixed internal communication problems Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552645 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552650 Loggerentry on negativ edge of SafeModuleOK If a negativ edge on SafeModuleOK is detected, a logger entry will be generated Channel description changed: No Configuration description changed: No Firmware changed: No ID: 553760 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(325) Version 1.10.1.0: ID: 474970 Correction for FBK_Status_1 Correction for FBK_Status_1 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 516730 fixed internal communication problems fixed internal communication problems Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552645 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552650 Loggerentry on negativ edge of SafeModuleOK If a negativ edge on SafeModuleOK is detected, a logger entry will be generated Channel description changed: No Configuration description changed: No Firmware changed: No ID: 553760 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(325) Version 1.10.0.6: ID: 533065 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533155 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533175 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(320) Version 1.10.0.0: ID: 402885 / Support ID: 400142740 Step File The step file is available since 14th November 2014. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 441620 / Support ID: 400159816 EPLAN Data for pinout - file corrected EPLAN Data for pinout - file corrected Channel description changed: No Configuration description changed: No Firmware changed: No ID: 470660 Support of release 1.10 including openSAFETY 1.5 Support of release 1.10 including openSAFETY 1.5 with easier parametrization of timing parameters Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 470665 changed manual verion to 1.100 changed manual verion to 1.100 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(320) Version 1.9.1.1: ID: 425470 change of input filter The behaviour of the input filter has changed. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 425475 Update Online Help Update Online Help V1.91 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 425480 fw valid from SafetyRelease 1.4 on The firmware is used for all SafetyReleases from 1.4 on. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301) Version 1.9.0.0: ID: 286520 / Support ID: 400082173 Diagnostic coverage not relevant for users Since the parameter "Diagnostic coverage" isn't relevant for users, it was generally removed from the datasheet of all safety modules. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 413875 SafeModuleID >300 Now it is possible to set SafeModuleID greater than 300, like described in the AS-Help. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414030 Channel-Status-Info ON The default value of the Channel-Status information is now ON. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414190 added parameter "Disable OSSD" added parameter "Disable OSSD" Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414250 parameter max. Switching Frequency removed Parameter max. Switching Frequency has no meaning any more. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes ID: 414295 2-channel evaluation: additional information at warning If warning "discrepancy time elapsed" appears for 2-channel evaluation, info0 will now display the chosen PLCopen FBK (equivalent or antivalent). Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 414370 Update Online Help Update Online Help V1.90 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290), 5\42918_1.fw(300) Version 1.6.0.8: ID: 388470 The module also supports SafetyRelease 1.8 Starting with this version, the module also supports SafetyRelease 1.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.7: ID: 339300 internal Adjustments internal Adjustments Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.5: ID: 335515 The module also supports SafetyRelease 1.7 Starting with this version, the module also supports SafetyRelease 1.7 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 335520 / Support ID: 400083263 unlock of SafeModule IDs > 300 SafeModule IDs up to 1023 are now unlocked Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.0: ID: 314285 Adaption of module configuration file release 1.6 Adaption of module configuration file release 1.6 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.5.0.4: ID: 303415 Support of AutomationStudio 4.0 Support of AutomationStudio 4.0 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.5.0.3: ID: 287445 New feature Discrepancy time maximum from 500ms to 10s increased. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 290270 Datasheet Version 1.50 Datasheet version 1.50 added in Html format Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.4.1.3: ID: 284655 Release für kompatibles Safety Release 1.5 ID 284600 Parameter for backwards compatibility in description file changed Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281) Version 1.4.0.3: ID: 261780 Increase of minimum load to 12mA The minimum load was increased to 12mA in the documentationErhöhung der Mindestlast auf 12mA Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.10.9.1 | * | 16.05.2019 | 3 MB | EXE | AS4_HW_X67SC4122.L12.exe | |
| Popis |
V4.0 HW Upgrade (X67SC4122.L12) Revision information X67SC4122.L12 Version 1.10.9.1: ID: 643220 data sheet V1.141 See chapture "Version history" in the data sheet. i.a. calculation of Safety response time has been updated. Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(330) Version 1.10.9.0: ID: 618290 logger entry 112174, 108078 Logger entry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(330) Version 1.10.1.1: ID: 516730 fixed internal communication problems fixed internal communication problems Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552645 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552650 Loggerentry on negativ edge of SafeModuleOK If a negativ edge on SafeModuleOK is detected, a logger entry will be generated Channel description changed: No Configuration description changed: No Firmware changed: No ID: 553760 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(325) Version 1.10.1.0: ID: 474970 Correction for FBK_Status_1 Correction for FBK_Status_1 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 516730 fixed internal communication problems fixed internal communication problems Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552645 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552650 Loggerentry on negativ edge of SafeModuleOK If a negativ edge on SafeModuleOK is detected, a logger entry will be generated Channel description changed:No Configuration description changed: No Firmware changed: No ID: 553760 New default values The default values for "Filter On"and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(325) Version 1.10.0.6: ID: 533065 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533155 New channel for ConnectionValid New channel for ConnectionValid Channel description changed:Yes Configuration description changed: No Firmware changed: No ID: 533175 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(320) Version 1.10.0.0: ID: 402885 / Support ID: 400142740 Step File The step file is available since 14th November 2014. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 441620 / Support ID: 400159816 EPLAN Data for pinout - file corrected EPLAN Data for pinout - file corrected Channel description changed: No Configuration description changed: No Firmware changed: No ID: 470660 Support of release 1.10 including openSAFETY 1.5 Support of release 1.10 including openSAFETY 1.5 with easier parametrization of timing parameters Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 470665 changed manual verion to 1.100 changed manual verion to 1.100 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(320) Version 1.9.1.1: ID: 425470 change of input filter The behaviour of the input filter has changed. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 425475 Update Online Help Update Online Help V1.91 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 425480 fw valid from SafetyRelease 1.4 on The firmware is used for all SafetyReleases from 1.4 on. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272),6\42918_1.fw(301) Version 1.9.0.0: ID: 286520 / Support ID: 400082173 Diagnostic coverage not relevant for users Since the parameter "Diagnostic coverage" isn't relevant for users, it was generally removed from the datasheet of all safety modules. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 413875 SafeModuleID >300 Now it is possible to set SafeModuleID greater than 300, like described in the AS-Help. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414030 Channel-Status-Info ON The default value of the Channel-Status information is now ON. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414190 added parameter "Disable OSSD" added parameter "Disable OSSD" Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414250 parameter max. Switching Frequency removed Parameter max. Switching Frequency has no meaning any more. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes ID: 414295 2-channel evaluation: additional information at warning If warning "discrepancy time elapsed" appears for 2-channel evaluation, info0 will now display the chosen PLCopen FBK (equivalent or antivalent). Channel description changed: No Configuration description changed: No Firmware changed: Yes ID:414370 Update Online Help Update Online Help V1.90 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290), 5\42918_1.fw(300) Version 1.6.0.8: ID: 388470 The module also supports SafetyRelease 1.8 Starting with this version, the module also supports SafetyRelease 1.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware:2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.7: ID: 339300 internal Adjustments internal Adjustments Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.5: ID: 335515 The module also supports SafetyRelease 1.7 Starting with this version, the module also supports SafetyRelease 1.7 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 335520 / Support ID: 400083263 unlock of SafeModule IDs > 300 SafeModule IDs up to 1023 are now unlocked Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.0: ID: 314285 Adaption of module configuration file release 1.6 Adaption of module configuration file release 1.6 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.5.0.4: ID: 303415 Support of AutomationStudio 4.0 Support of AutomationStudio 4.0 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.5.0.3: ID: 287445 New feature Discrepancy time maximum from 500ms to 10s increased. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 290270 Datasheet Version 1.50 Datasheet version 1.50 added in Html format Channeldescription changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.4.1.3: ID: 284655 Release für kompatibles Safety Release 1.5 ID 284600 Parameter for backwards compatibility in description file changed Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281) Version 1.4.0.3: ID: 261780 Increase of minimum load to 12mA The minimum load was increased to 12mA in the documentationErhöhung der Mindestlast auf 12mA Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.10.9.0 | * | 08.11.2018 | 3 MB | EXE | AS4_HW_X67SC4122.L12.exe | |
| Popis |
V4.0 HW Upgrade (X67SC4122.L12) Revision information X67SC4122.L12 Version 1.10.9.0: ID: 618290 logger entry 112174, 108078 Logger entry 112174, 108078 could happen sporadically with large projects. Channel description changed: No Configuration description changed: No Firmware changed: Yes Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(330) Version 1.10.1.1: ID: 516730 fixed internal communication problems fixed internal communication problems Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552645 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552650 Loggerentry on negativ edge of SafeModuleOK If a negativ edge on SafeModuleOK is detected, a logger entry will be generated Channel description changed: No Configuration description changed: No Firmware changed: No ID: 553760 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(325) Version 1.10.1.0: ID: 474970 Correction for FBK_Status_1 Correction for FBK_Status_1 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 516730 fixed internal communication problems fixed internal communication problems Channel description changed: No Configuration descriptionchanged: No Firmware changed: No ID: 552645 Provide CRC ofthe Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552650 Loggerentry on negativ edge of SafeModuleOK If a negativ edge on SafeModuleOK is detected, a logger entry will be generated Channel description changed: No Configuration description changed: No Firmware changed: No ID: 553760 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(325) Version 1.10.0.6: ID: 533065 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533155 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533175 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(320) Version 1.10.0.0: ID: 402885 /Support ID: 400142740 Step File The step file is available since 14th November 2014. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 441620 / Support ID: 400159816 EPLAN Data for pinout - file corrected EPLAN Data for pinout - file corrected Channel description changed: No Configuration description changed: No Firmware changed: No ID: 470660 Support of release 1.10 including openSAFETY 1.5 Support of release 1.10 including openSAFETY 1.5 with easier parametrization of timing parameters Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 470665 changed manual verion to 1.100 changed manual verion to 1.100 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware:2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(320) Version 1.9.1.1: ID: 425470 change of input filter The behaviour of the input filter has changed. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 425475 Update Online Help Update Online Help V1.91 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 425480 fw valid from SafetyRelease 1.4 on The firmware is used for all SafetyReleases from 1.4 on. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301) Version 1.9.0.0: ID: 286520 / Support ID: 400082173 Diagnostic coverage not relevant forusers Since the parameter "Diagnostic coverage" isn't relevant for users, it was generally removed from the datasheet of all safety modules. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 413875 SafeModuleID >300 Now it is possible to set SafeModuleID greater than 300, like described in the AS-Help. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414030 Channel-Status-Info ON The default value of the Channel-Status information is now ON. Channeldescription changed: No Configuration description changed: Yes Firmware changed: No ID: 414190 added parameter "Disable OSSD" added parameter "Disable OSSD" Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414250 parameter max. Switching Frequency removed Parameter max. Switching Frequency has no meaning any more. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes ID: 414295 2-channel evaluation: additional information at warning If warning "discrepancy time elapsed" appears for 2-channel evaluation, info0 will now display the chosen PLCopen FBK (equivalent or antivalent). Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 414370 Update Online Help Update OnlineHelp V1.90 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290), 5\42918_1.fw(300) Version 1.6.0.8: ID: 388470 The module also supports SafetyRelease 1.8 Starting with this version, the module also supports SafetyRelease 1.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.7: ID: 339300 internal Adjustments internal Adjustments Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.5: ID: 335515 The module also supports SafetyRelease 1.7 Starting withthis version, the module also supports SafetyRelease 1.7 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 335520 / Support ID: 400083263 unlock of SafeModule IDs > 300 SafeModule IDs up to 1023 are now unlocked Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.0: ID: 314285 Adaption of module configuration file release 1.6 Adaption of module configuration file release 1.6 Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.5.0.4: ID: 303415 Support of AutomationStudio 4.0 Support of AutomationStudio 4.0 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.5.0.3: ID: 287445 New feature Discrepancy time maximum from 500ms to 10s increased. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 290270 Datasheet Version 1.50 Datasheet version 1.50 addedin Html format Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.4.1.3: ID: 284655 Release für kompatibles Safety Release 1.5 ID 284600 Parameter for backwards compatibility in description file changed Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281) Version 1.4.0.3: ID: 261780 Increase of minimum load to 12mA The minimum load was increased to 12mA in the documentationErhöhung der Mindestlast auf 12mA Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281) |
|||||
| Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
| 1.10.1.1 | * | 14.12.2017 | 3 MB | EXE | AS4_HW_X67SC4122.L12.exe | |
| Popis |
V4.0 HW Upgrade (X67SC4122.L12) Revision information X67SC4122.L12 Version 1.10.1.1: ID: 516730 fixed internal communication problems fixed internal communication problems Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552645 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552650 Loggerentry on negativ edge of SafeModuleOK If a negativ edge on SafeModuleOK is detected,a logger entry will be generated Channel description changed: No Configuration description changed: No Firmware changed: No ID: 553760 New default values The default values for "Filter On" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(325) Version 1.10.1.0: ID: 474970 Correction for FBK_Status_1 Correction for FBK_Status_1 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 516730 fixed internal communication problems fixed internal communication problems Channel description changed: No Configuration description changed: No Firmware changed: No ID: 552645 Provide CRC of the Firmware Provide CRC of the Firmware Channel description changed: No Configurationdescription changed: No Firmware changed: No ID: 552650 Loggerentry on negativ edge of SafeModuleOK If a negativ edge on SafeModuleOK is detected, a logger entry will be generated Channel description changed: No Configuration description changed: No Firmware changed: No ID: 553760 New default values The default values for "FilterOn" and "Discrepancy Time" have been modified Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(325) Version 1.10.0.6: ID: 533065 Add blackout mode Add blackout mode Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533155 New channel for ConnectionValid New channel for ConnectionValid Channel description changed: Yes Configuration description changed: No Firmware changed: No ID: 533175 Update ECAD data Update ECAD data Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(320) Version 1.10.0.0: ID: 402885 / Support ID: 400142740 Step File The step file is available since 14th November 2014. Channel description changed: No Configuration description changed: No Firmware changed: No ID: 441620 / Support ID: 400159816 EPLAN Data for pinout - file corrected EPLAN Data for pinout - file corrected Channel description changed: No Configuration description changed: No Firmware changed: No ID: 470660 Support of release 1.10 including openSAFETY 1.5 Support of release 1.10 including openSAFETY 1.5 with easier parametrization of timing parameters Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 470665 changed manual verion to 1.100 changed manual verion to 1.100 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301), 7\42918_1.fw(320) Version 1.9.1.1: ID: 425470 change of input filter The behaviour of the input filter has changed. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 425475 Update Online Help Update Online Help V1.91 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 425480 fw valid from SafetyRelease 1.4 on The firmware is used for all SafetyReleases from 1.4 on. Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 6\42918_1.fw(301) Version 1.9.0.0: ID: 286520 / Support ID: 400082173 Diagnostic coverage not relevant for users Since the parameter "Diagnostic coverage" isn't relevant for users, it was generally removed from the datasheet of all safety modules. Channel description changed:No Configuration description changed: No Firmware changed: No ID: 413875 SafeModuleID >300 Now it is possible to set SafeModuleID greater than 300, like described in the AS-Help. Channel description changed: No Configuration description changed: Yes Firmware changed:No ID: 414030 Channel-Status-Info ON The default value of the Channel-Status information is now ON. Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414190 added parameter "Disable OSSD" added parameter "DisableOSSD" Channel description changed: No Configuration description changed: Yes Firmware changed: No ID: 414250 parameter max. Switching Frequency removed Parameter max. Switching Frequency has no meaning any more. Channel description changed: Yes Configuration description changed: No Firmware changed: Yes ID: 414295 2-channel evaluation: additional information at warning If warning "discrepancy time elapsed" appears for 2-channel evaluation, info0 will now display the chosenPLCopen FBK (equivalent or antivalent). Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 414370 Update Online Help Update Online Help V1.90 Channeldescription changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290), 5\42918_1.fw(300) Version 1.6.0.8: ID: 388470 The module also supports SafetyRelease 1.8 Starting with this version, themodule also supports SafetyRelease 1.8 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.7: ID: 339300 internal Adjustments internal Adjustments Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.5: ID: 335515 The module also supports SafetyRelease 1.7 Starting with this version, the module also supports SafetyRelease 1.7 Channel description changed: No Configuration description changed: No Firmware changed: No ID: 335520 / Support ID: 400083263 unlock of SafeModule IDs > 300 SafeModule IDs up to 1023 are now unlocked Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.6.0.0: ID: 314285 Adaption of module configuration file release 1.6 Adaption of module configuration file release 1.6 Channel description changed: No Configuration description changed: Yes Firmware changed:No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.5.0.4: ID: 303415 Support of AutomationStudio 4.0 Support of AutomationStudio 4.0 Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.5.0.3: ID: 287445 New feature Discrepancy time maximum from 500ms to 10s increased. Channel description changed: No Configuration description changed: No Firmware changed: Yes ID: 290270 Datasheet Version 1.50 Datasheet version 1.50 added in Html format Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281), 4\42918_1.fw(290) Version 1.4.1.3: ID: 284655 Release für kompatibles Safety Release 1.5 ID 284600 Parameter for backwards compatibility in description file changed Channel description changed: No Configuration description changed: Yes Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281) Version 1.4.0.3: ID: 261780 Increase of minimum load to 12mA The minimum load was increased to 12mA in the documentationErhöhung der Mindestlast auf 12mA Channel description changed: No Configuration description changed: No Firmware changed: No Firmware: 2\42918_1.fw(272), 3\42918_1.fw(281) |
|||||
