DWL@DWL10000544020
Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
---|---|---|---|---|---|---|
1.32 | * | 16.01.2023 | 4 MB | ZIP | UPG_APC910_MTCX_V0132_EFI.zip | |
Popis |
APC910 Firmware Upgrade (MTCX, SDLT, SDL3T, SDL4T) for EFI ---------------------------------------------------------------- ATTENTION! Possible upgrade problems and version dependency ---------------------------------------------------------------- 1. Do not reset or switch off the device during the upgrade process !!! 2. If a UPS is connected to the system, the battery unit must be disconnected or the Power button must be pressed (to set the system in standby mode) after the upgrade of the MTCX is done, but before the required Power Off/On is done. Otherwise the firmware upgrade is not complete, because the UPS will provide the system with power. 3. When upgrading SDL4 components, no CAN IF option (5AC901.ICAN-00 or 5AC901.ICAN-01) is allowed to be plugged. 4. A Extended upgrade for the SDL4T Firmware is only necessary if an SDL4T firmware less than V01.00 is installed. 5. Starting with SDL4T Firmware V01.00, a downgrade to a version smaller then V01.00 is not possible. 6. Starting with SDL4T Firmware V01.00, a Automation Panel Firmware update for the SDL4R Firmware at least from V06.14 and HDBT Firmware at least from V01.00 is necessary. ---------------------------------------------------------------- Version 01.32 / 11/07/2022 / MIK !MANDATORY UPDATE! ---------------------------------------------------------------- Content LIESMICH.txt 01.32 NEW README.txt 01.32 NEW STARTUP.nsh 01.32 NEW MTCXAPC910.nsh 01.24 SDLTAPC910.nsh 01.28 MTCXSVC.efi 19.52 55002_0.fw 01.32 55002_0.fw 01.32 55363_0.fw 01.32 55364_0.fw 01.32 55379_0.fp (SDLT) 00.09 58368_0.fp (SDL3T) 00.19 60622_0.fp (SDL4T) 01.04 NEW 60622i0.fp (SDL4TExt.) 01.04 NEW Change(s) 60622_0.fp (FPGA FW f. 5AC901.LSD4-00): - Updated HDBASET2 FW: A RFID reader was not recognized sporadically during a PowerOn using ARemb. After a warm start this behaviour could not be observed in ARemb. Also under GPOS operating systems, such as Windows 10 this behaviour could not be observed. 60622i0.fp (Extended FPGA FW f. 5AC901.LSD4-00): - Updated HDBASET2 FW: A RFID reader was not recognized sporadically during a PowerOn using ARemb. After a warm start this behaviour could not be observed in ARemb. Also under GPOS operating systems, such as Windows 10 this behaviour could not be observed. INFORMATION: This upgrade is only necessary if an SDL4T firmware less than V01.00 is installed. ATTENTION: Do not reset or switch off the device during the upgrade process! ATTENTION! Possible upgrade problems and version dependency, see above. |
|||||
Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
1.31 | * | 05.10.2022 | 4 MB | ZIP | UPG_APC910_MTCX_V0131_EFI.zip | |
Popis |
APC910 Firmware Upgrade (MTCX, SDLT, SDL3T, SDL4T) for EFI ---------------------------------------------------------------- ATTENTION! Possible upgrade problems and version dependency ---------------------------------------------------------------- 1. Do not reset or switch off the device during the upgrade process !!! 2. If a UPS is connected to the system, the battery unit must be disconnected or the Power button must be pressed (to set the system in standby mode) after the upgrade of the MTCX is done, but before the required Power Off/On is done. Otherwise the firmware upgrade is not complete, because the UPS will provide the system with power. 3. A Extended upgrade for the SDL4T Firmware is only necessary if an SDL4T firmware less than V01.00 is installed. 4. Starting with SDL4T Firmware V01.00, a downgrade to a version smaller then V01.00 is not possible. 5. Starting with SDL4T Firmware V01.00, a Automation Panel Firmware update for the SDL4R Firmware at least from V06.14 and HDBT Firmware at least from V01.00 is necessary. ---------------------------------------------------------------- Version 01.31 / 08/19/2022 / MIK !MANDATORY UPDATE! ---------------------------------------------------------------- Content LIESMICH.txt 01.31 NEW README.txt 01.31 NEW STARTUP.nsh 01.24 MTCXAPC910.nsh 01.24 SDLTAPC910.nsh 01.28 MTCXSVC.efi 19.52 55002_0.fw 01.32 NEW 55002_0.fw 01.32 NEW 55363_0.fw 01.32 NEW 55364_0.fw 01.32 NEW 55379_0.fp (SDLT) 00.09 58368_0.fp (SDL3T) 00.19 60622_0.fp (SDL4T) 01.02 60622i0.fp (SDL4TExt.) 01.02 Change(s) 55002_0.fw (MTCX f. 5PC910.SX01-00): - Optimized internal power supply. 55003_0.fw (MTCX f. 5PC910.SX02-00): - Optimized internal power supply. 55363_0.fw (MTCX f. 5PC910.SX03-00): - Optimized internal power supply. 55364_0.fw (MTCX f. 5PC910.SX05-00): - Optimized internal power supply. ATTENTION! Possible upgrade problems and version dependency, see above. |
|||||
Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
1.30 | * | 13.06.2022 | 4 MB | ZIP | UPG_APC910_MTCX_V0130_EFI.zip | |
Popis |
APC910 Firmware Upgrade (MTCX, SDLT, SDL3T, SDL4T) for EFI ---------------------------------------------------------------- ATTENTION! Possible upgrade problems and version dependency ---------------------------------------------------------------- 1. Do not reset or switch off the device during the upgrade process !!! 2. If a UPS is connected to the system, the battery unit must be disconnected or the Power button must be pressed (to set the system in standby mode) after the upgrade of the MTCX is done, but before the required Power Off/On is done. Otherwise the firmware upgrade is not complete, because the UPS will provide the system with power. 3. A Extended upgrade for the SDL4T Firmware is only necessary if an SDL4T firmware less than V01.00 is installed. 4. Starting with SDL4T Firmware V01.00, a downgrade to a version smaller then V01.00 is not possible. 5. Starting with SDL4T Firmware V01.00, a Automation Panel Firmware update for the SDL4R Firmware at least from V06.14 and HDBT Firmware at least from V01.00 is necessary. ---------------------------------------------------------------- Version 01.30 / 03/24/2022 / MIK !MANDATORY UPDATE! ---------------------------------------------------------------- Content LIESMICH.txt 01.30 NEW README.txt 01.30 NEW STARTUP.nsh 01.24 MTCXAPC910.nsh 01.24 SDLTAPC910.nsh 01.28 MTCXSVC.efi 19.52 NEW 55002_0.fw 01.31 NEW 55002_0.fw 01.31 NEW 55363_0.fw 01.31 NEW 55364_0.fw 01.31 NEW 55379_0.fp (SDLT) 00.09 58368_0.fp (SDL3T) 00.19 60622_0.fp (SDL4T) 01.02 60622i0.fp (SDL4TExt.) 01.02 Change(s) 55002_0.fw (MTCX f. 5PC910.SX01-00): - Optimization of the SDL interface in combination with DVI panels. 55003_0.fw (MTCX f. 5PC910.SX02-00): - Optimization of the SDL interface in combination with DVI panels. 55363_0.fw (MTCX f. 5PC910.SX03-00): - Optimization of the SDL interface in combination with DVI panels. 55364_0.fw (MTCX f. 5PC910.SX05-00): - Optimization of the SDL interface in combination with DVI panels. MTCXSVC: - Minor optimizations and bug fixes. ATTENTION! Possible upgrade problems and version dependency, see above. |
|||||
Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
1.29 | * | 08.06.2021 | 4 MB | ZIP | UPG_APC910_MTCX_V0129_EFI.zip | |
Popis |
APC910 Firmware Upgrade (MTCX, SDLT, SDL3T, SDL4T) for EFI ---------------------------------------------------------------- ATTENTION! Possible upgrade problems and version dependency ---------------------------------------------------------------- 1. Do not reset or switch off the device during the upgrade process !!! 2. If a UPS is connected to the system, the battery unit must be disconnected or the Power button must be pressed (to set the system in standby mode) after the upgrade of the MTCX is done, but before the required Power Off/On is done. Otherwise the firmware upgrade is not complete, because the UPS will provide the system with power. 3. A Extended upgrade for the SDL4T Firmware is only necessary if an SDL4T firmware less than V01.00 is installed. 4. Starting with SDL4T Firmware V01.00, a downgrade to a version smaller then V01.00 is not possible. 5. Starting with SDL4T Firmware V01.00, a Automation Panel Firmware update for the SDL4R Firmware at least from V06.14 and HDBT Firmware at least from V01.00 is necessary. ---------------------------------------------------------------- Version 01.29 / 02/08/2021 / MIK !MANDATORY UPDATE! ---------------------------------------------------------------- Content LIESMICH.txt 01.29 NEW README.txt 01.29 NEW STARTUP.nsh 01.24 MTCXAPC910.nsh 01.24 SDLTAPC910.nsh 01.28 MTCXSVC.efi 19.40 55002_0.fw 01.27 55002_0.fw 01.27 55363_0.fw 01.27 55364_0.fw 01.27 55379_0.fp (SDLT) 00.09 58368_0.fp (SDL3T) 00.19 60622_0.fp (SDL4T) 01.02 NEW 60622i0.fp (SDL4TExt.) 01.02 NEW Change(s) 60622_0.fp (FPGA FW f. 5AC901.LSD4-00): - Updated HDBASET2 FW: USB communication in combination with USB 3.0 devices optimized. 60622i0.fp (Extended FPGA FW f. 5AC901.LSD4-00): - Updated HDBASET2 FW: USB communication in combination with USB 3.0 devices optimized. INFORMATION: This upgrade is only necessary if an SDL4T firmware less than V01.00 is installed. ATTENTION: Do not reset or switch off the device during the upgrade process! ATTENTION! Possible upgrade problems and version dependency, see above. |
|||||
Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
1.28 | * | 17.09.2020 | 4 MB | ZIP | UPG_APC910_MTCX_V0128_EFI.zip | |
Popis |
APC910 Firmware Upgrade (MTCX, SDLT, SDL3T, SDL4T) for EFI ---------------------------------------------------------------- ATTENTION! Possible upgrade problems and version dependency ---------------------------------------------------------------- 1. Do not reset or switch off the device during the upgrade process !!! 2. If a UPS is connected to the system, the battery unit must be disconnected or the Power button must be pressed (to set the system in standby mode) after the upgrade of the MTCX is done, but before the required Power Off/On is done. Otherwise the firmware upgrade is not complete, because the UPS will provide the system with power. ---------------------------------------------------------------- Version 01.27 / 05/20/2019 / MIK !MANDATORY UPDATE! ---------------------------------------------------------------- Content LIESMICH.txt 01.27 NEW README.txt 01.27 NEW STARTUP.nsh 01.24 MTCXAPC910.nsh 01.24 SDLTAPC910.nsh 01.24 MTCXSVC.efi 17.43 55002_0.fw 01.27 NEW 55002_0.fw 01.27 NEW 55364_0.fw 01.27 NEW 55379_0.fp (SDLT) 00.08 58368_0.fp (SDL3T) 00.19 60622_0.fp (SDL4T) 00.04 Change(s) 55002_0.fw (MTCX f. 5PC910.SX01-00): - Optimized internal keyboard syncronization. - Optimized internal power supply syncronization. 55003_0.fw (MTCX f. 5PC910.SX02-00): - Optimized internal keyboard syncronization. - Optimized internal power supply syncronization. 55364_0.fw (MTCX f. 5PC910.SX05-00): - Optimized internal keyboard syncronization. - Optimized internal power supply syncronization. ATTENTION! Possible upgrade problems and version dependency, see above. |
|||||
Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
1.27 | * | 09.08.2019 | 2 MB | ZIP | UPG_APC910_MTCX_V0127_EFI.zip | |
Popis |
APC910 Firmware Upgrade (MTCX, SDLT, SDL3T, SDL4T) for EFI ---------------------------------------------------------------- ATTENTION! Possible upgrade problems and version dependency ---------------------------------------------------------------- 1. Do not reset or switch off the device during the upgrade process !!! 2. If a UPS is connected to the system, the battery unit must be disconnected or the Power button must be pressed (to set the system in standby mode) after the upgrade of the MTCX is done, but before the required Power Off/On is done. Otherwise the firmware upgrade is not complete, because the UPS will provide the system with power. ---------------------------------------------------------------- Version 01.27 / 05/20/2019 / MIK !MANDATORY UPDATE! ---------------------------------------------------------------- Content LIESMICH.txt 01.27 NEW README.txt 01.27 NEW STARTUP.nsh 01.24 MTCXAPC910.nsh 01.24 SDLTAPC910.nsh 01.24 MTCXSVC.efi 17.43 55002_0.fw 01.27 NEW 55002_0.fw 01.27 NEW 55364_0.fw 01.27 NEW 55379_0.fp (SDLT) 00.08 58368_0.fp (SDL3T) 00.19 60622_0.fp (SDL4T) 00.04 Change(s) 55002_0.fw (MTCX f. 5PC910.SX01-00): - Optimized internal keyboard syncronization. - Optimized internal power supply syncronization. 55003_0.fw (MTCX f. 5PC910.SX02-00): - Optimized internal keyboard syncronization. - Optimized internal power supply syncronization. 55364_0.fw (MTCX f. 5PC910.SX05-00): - Optimized internal keyboard syncronization. - Optimized internal power supply syncronization. ATTENTION! Possible upgrade problems and version dependency, see above. |
|||||
Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
1.26 | * | 14.12.2018 | 2 MB | ZIP | UPG_APC910_MTCX_V0126_EFI.zip | |
Popis |
APC910 Firmware Upgrade (MTCX, SDLT, SDL3T, SDL4T) for EFI ---------------------------------------------------------------- ATTENTION! Possible upgrade problems and version dependency ---------------------------------------------------------------- 1. Do not reset or switch off the device during the upgrade process !!! 2. If a UPS is connected to the system, the battery unit must be disconnected or the Power button must be pressed (to set the system in standby mode) after the upgrade of the MTCX is done, but before the required Power Off/On is done. Otherwise the firmware upgrade is not complete, because the UPS will provide the system with power. ---------------------------------------------------------------- Version 01.26 / 07/23/2018 / MIK !MANDATORY UPDATE! ---------------------------------------------------------------- Content LIESMICH.txt 01.26 NEW README.txt 01.26 NEW STARTUP.nsh 01.24 MTCXAPC910.nsh 01.24 SDLTAPC910.nsh 01.24 MTCXSVC.efi 17.43 NEW 55002_0.fw 01.25 NEW 55002_0.fw 01.25 NEW 55364_0.fw 01.25 NEW 55379_0.fp (SDLT) 00.08 NEW 58368_0.fp (SDL3T) 00.19 60622_0.fp (SDL4T) 00.04 Change(s) 55002_0.fw (MTCX f. 5PC910.SX01-00): - Support for IF option 5AC901.I232-00 implemented. - Enhancements for B&R Hypervisor. 55003_0.fw (MTCX f. 5PC910.SX02-00): - Support for IF option 5AC901.I232-00 implemented. - Enhancements for B&R Hypervisor. 55364_0.fw (MTCX f. 5PC910.SX05-00): - Support for IF option 5AC901.I232-00 implemented. - Enhancements for B&R Hypervisor. 55379.fp (FPGA FW f. 5AC901.LSDL-00): - Bugfix: secure FW update. In very rare cases a faulty or uncomplete FW update was shown falsely. MTCXSVC: - Support for xPC2200 family. - Support for SDL4 converter. ATTENTION! Possible upgrade problems and version dependency, see above. |
|||||
Verze | Jazyk | Operační systém | Datum | Velikost | Typ | Stáhnout |
1.25 | * | 23.05.2018 | 2 MB | ZIP | UPG_APC910_MTCX_V0125_EFI.zip | |
Popis |
APC910 Firmware Upgrade (MTCX, SDLT, SDL3T, SDL4T) For EFI ---------------------------------------------------------------- ATTENTION! Possible upgrade problems and version dependency ---------------------------------------------------------------- 1. Do not reset or switch off the device during the upgrade process !!! 2. If a UPS is connected to the system, the battery unit must be disconnected or the Power button must be pressed (to set the system in standby mode) after the upgrade of the MTCX is done, but before the required Power Off/On is done. Otherwise the firmware upgrade is not complete, because the UPS will provide the system with power. ---------------------------------------------------------------- Version 01.25 / 04/26/2018 / MIK !MANDATORY UPDATE! ---------------------------------------------------------------- Content LIESMICH.txt 01.25 NEW README.txt 01.25 NEW STARTUP.nsh 01.24 MTCXAPC910.nsh 01.24 SDLTAPC910.nsh 01.24 MTCXSVC.efi 16.10 55002_0.fw 01.24 55002_0.fw 01.24 55364_0.fw 01.24 55379_0.fp (SDLT) 00.07 58368_0.fp (SDL3T) 00.19 NEW 60622_0.fp (SDL4T) 00.04 NEW Change(s) 58368.fp (FPGA FW f. 5AC901.LSD3-00): - Bugfix: SDL3 communication. In very rare cases a problem occured during poweron, that the SDL3 communication is not stable. 60622.fp (FPGA FW f. 5AC901.LSD4-00): - Updated HDBASET2 FW. ATTENTION! Possible upgrade problems and version dependency, see above. |